How to Put Fishing Line on Spinning Reel: Step By Step

Fishing is meant to be an exciting and relaxing adventure. You will feel wasted if your fishing line keeps on tangling and twisting. At the end of the day, your targeted catch will not have been achieved. It's important that you are well versed with the procedure of loading and spooling the reel to avoid some of these inconveniences.

The reel’s capacity determines what type and size of the fishing line go into it. Before looking at the procedure of spooling your spinning reel, it's of great importance to understand what a reel capacity means. Every spinning reel has the specs outlined as; type/ lb. (yds.) For example, Nylon Mono 50(120).

The Reel’s Capacity Determine

The Type of Line

It is clearly stipulated either as nylon mono, braided, and fluorocarbon just to mention but a few. It is advised that you stick to the specified line type to avoid disappointments. Braided line is the most preferred by many beginners because it does not show more twists.

Line Weight

After the type, the very first number refers to the weight of the line the reel is equipped to hold. Your line should therefore, be less or exactly the same as the stated weight. Exceeding the weight can result in the breaking of the rod or the line itself eventually.

The Length of the Line

The second number means the length in yards of fishing line that the reel supports. For improved efficiency, the line ought not to exceed the stipulated length.

The fishing line is an interconnecting factor between the fish, the rod and yourself. Putting a fishing line on a spinning reel is probably the first idea you should learn before starting your fishing expedition. It takes only about 10 minutes to finish this simple procedure.

Which Line is Better Braided Line or Monofilament Line, Check Out This

Step by Step Guidance on Loading Your Spinning Reel

You should be able to determine the direction the reel turns towards to. Simply do this by holding the reel in the actual way you could do when you are fishing. Then turn the wheel for about three times while observing the direction it is moving, this is the same way you will spool the line on the reel.

Kindly follow the detailed procedure outlined below keenly on how to spool your reel with a fishing line.

Step 1

Flip open the bail. This refers to a small arm on your reel that flips down to close and up to open. Remove any old line if the reel has been used before. Take your fishing line and thread it through the guides starting from the one on the top and work your way down towards the hole near the spool.

Are you facing problem to clean a fishing reel after saltwater use? check out this blog post.

Step 2

After that, take the line and tie it firmly to the spool with an arbor knot. Tie another knot just about 2.5 cm from the previous one. The next step is to pull the standing line and let it slide down the first knot you had made to the spool. Lastly, slide your second knot to the first one.

Step 3

Leave about a quarter of an inch of the fishing line after tying the second knot and cut off any excess using a scissor or a line cutter. An overhand knot is the best recommended as it ensures the line is secured on the spool. Close the bail by flipping down the arm.

Step 4

Place the spool with the label on the on the top side on a flat surface. Take note to wrap the line on the reel the same manner it goes off the spool. Take the mainline then apply little pressure as you wrap it around the reel by using your index finger. This prevents the line from going loose and tangling. Keep rotating the handle for about 15 times and check it for any twists.

Step 5

Should the line have any twists, unwrap it, place the spool upside down and start all over again. Apart from that, you can just go back to where the twist is, straighten it up slowly and continue with the wrapping.

Step 6

Don’t overload the spool. Leave about 1/8 of an inch to the rim so that you can see a part of the spool. Neither are you required to under fill it. If that small space is not left, your line may tangle up or even make you encounter other problems when casting. 

Step 7

When you are done spooling the reel,leave some extra line and then cut the remaining fishing line closer to the supply spool. Take your lure or bait and tie it to the hanging end of the line. This is done to prevent your line from slipping back through the guides. In case the spool comes with a tab attached to it, simply tie the hanging line around it.

Step 8

Alternatively, you can tape or rubber band the open end of your supply spool to secure your line to avoid it to unravel when moving around in the tackle box. Congrats! You’ve now spooled your reel successfully.

Each of the above steps should be followed strictly from the first to the latter if you are enthusiastic about using a spinning reel efficiently for uncompromised fishing. It won't hurt a bunch to redo the whole process if you missed out on anything. Hey! It’s all for your own benefit.

As an extra tip, consider having several spools with each filled with different weight line for your reel. This comes in handy when maneuvering between various water surfaces. When you are fishing in weeds or muddy water, use the spool with a thicker or heavier line and a spool with a thin and lightline for the clear waters. This helps minimize time and increase your maximum output.

You May Also Like to Read: Boning Knife VS Fillet Knife.

Conclusion

In conclusion, the above points can be summarized in a simple phrase “the fishing line and the spinning reel work hand in hand.” If the reel is properly loaded, it minimizes line twisting or tangling of the line and provides problem-free fishing. On the contrary, the opposite will happen if you don’t load your reel properly.

Click Here to Leave a Comment Below 0 comments

Leave a Reply: